Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008

Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008
Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008

Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008

Auger, Spinner, Hub, Harness Wire with plug, 12V Motor & hdwe. Salt Spreader Repair Kit includes: After market parts including: (1) Auger - MEYER #36151 & BUYERS #0202100. (1) Spinner 9 diameter 12 gauge stainless steel - Replacement Part #36163 & #0202600. (1) Harness Wire with Plug: Meyer 15727 Buyers #0203200. Repairs Meyer 36000, 36003 Meyer Salt spreaders.

(1) 12 V Motor - Direct Drive motor for low amp draw with maximum torque Heavy duty sealed ball bearing. Works with in-cab solid-state speed control.

Woodruff key Rotation: Bi-Directional Field Housing O. Overall Length: 6.941 in. Shaft Outside Diameter: 0.500 in.

Shaft Style: Includes Keyway and Woodruff Key. Terminal 1 Size: 1/4 - 20 Terminal 2 Size: 1/4 - 20 Housing Finish: Field case is black Weight: 12.43 lbs Includes square mounting plate with 4 mounting holes. (Meyers) OEM#36218, 36402 & (Buyers) OEM#0202000. The Salt Spreader Repair Kit. 36151 - Auger 36152 - Hub 36218 - Motor 36155 = 36151, 36163, 36152 - Auger, Spinner, Hub Assembly Kit 36163 - Spinner 36241 - Harness Wire with plug, Red & Black Lead Wire APPLICATION: (Will repair the following Salt Spreaders) TGS01, TGS01A, TGS01B, TGS05A, TGSUVPRO, TGUVPROA This kit is for Repairing Buyers and Meyers Salt Spreaders. THESE ARE REPLACEMENT PARTS FOR REPAIRING MEYER SPREADERS. THESE ARE NOT GENUINE MEYER PARTS. Weight: 12.43 lbs Includes square mounting plate with 4 mounting holes. The new schematics from Meyer show a poly spinner. Thank you for shopping with us.

Happy Snow Plow Season Everyone!!! ARE YOU READY FOR THE SNOW? Everyone is getting ready for another snow season. Winter will be here soon.

Here are some tips to get your snow plow or spreader ready for winter. Spreaders: Well spreaders, especially hopper style spreaders, arent easy to maintain. The first start up is always the most difficult, but it is very important to prepare your hopper spreader for summer storage, but we want to help you to get your spreader ready for winter. First, if you have gas engine spray with lubricating oil e. WD40 throttle linkage, make sure that all levers are moving smoothly.

Tip: Since the upper end of the starter and bendix on many engines is covered we recommend to drill (if possible) a small hole above to allow you to spray lubricant on to the bendix and armature shaft. Clean connections at the external battery (if you have one). Grease and inspect all bearings.

Lubricate clutch bearing (do not spray oil on pressure plate) Inspect conveyor chain, adjust tension if necessary Tip: to adjust measure about 24 from the rear edge of the hopper. Move up on the chain with your hand. The conveyor chain should lift up 1"-3" off the conveyor chain guide or cross braces. Change oil in gear box. If you have electric motor clean and inspect brushes, they should move freely most motors have access covers A salt spreader is an invaluable tool during the winter time. As ice builds up on your freshly plowed driveway, you will need to have some way to dissolve that ice. Salt works against the ice to melt it away so you are not slipping and sliding around your driveway. However, the ordinary homeowner will have a push behind or tow behind salt spreader. Keeping them clean and functioning will make your winter time clean up a lot more enjoyable.

Part of that cleaning is to keep your salt spreader maintained by troubleshooting it. When the spreader stops spreading salt evenly, or even at all, you should take some time to find out what is wrong with it instead of just throwing it away.

Common to all salt spreaders, whether it is a small walk behind or a tailgate spreader, is that it will begin to lay salt unevenly. An uneven spread of salt will lead to parts of the driveway, or parking lot, that is still covered with ice. This is a very dangerous situation as you can still start into a slide and not stop where you need to. Troubleshooting this means looking into the spreader to see if anything is lodged into the gearing. Make sure if you have an electrical spreader that it is unplugged from the power source.

This is mostly seen in a tailgate spreader. Use a small screwdriver to pry loose any stuck rocks, or hard pieces of salt.

Gears Are Squeaking Towards the end of the winter season you will probably hear some squeaking of the gear or internal workings in your spreader. By going through snow, freezing rain, thawing out, and all the salt that runs through the machine in a season, the spreader will begin to run out of lubricant. Some spreaders have grease fittings that can be used for greasing the internal workings. Other spreaders just need some silicone sprayed into the moving areas to keep them from squealing or sticking. No Salt Being Dropped You may notice that there isn't any salt being dropped onto your driveway. When this happens one of two things can be happening.

The first is that the door that opens to start the spreading is stuck. Check the underneath of the spreader and look at the opening mechanism. Check the spring that moves the door. Clean them out of any build up or replace the parts that are broken. The second thing that can happen in the cable has snapped.

If you have owned your salt spreader for awhile, this can easily be the cause. Spreading Salt If you notice that the salt is clumping together instead of spreading on the ground, there is excess moisture, snow, rain, sand in the mixture. You can add a cover to fix this problem, or add new salt to the spreader. Depending on the size of your salt spreader, the problem of salt clumps can be easy or difficult to fix. Below are some suggestions on how to get your salt spreader working again.

Materials Needed -Salt spreader -Warm space -Gloves -Hot water -Larger container or power washer Step 1-Warm Up Salt If your salt spreader is small enough, or if you have a big enough building, take your salt spreader indoors. Often times, once the salt has warmed back up it will loosen up and come out. It can take up to two days to thaw if you have a very large salt spreader, though this may not work for your situation. Step 2-Remove Excess Salt Depending on the type of salt spreader you have, you can dump or scoop out excess salt.

Dump it if it is a hand spreader; scoop it if it is similar to a tailgate spreader. Step 3-Try To Turn Spinner Sometimes it can be as simple as turning the spinner to remove the salt that is in the gears. Look to see if there are a few pieces which you can remove or break up by hand. Step 5-Turn On Salt Spreaders Vibrator If your salt spread has a vibrator you should turn it on to try to help loosen the salt up.

With a hand held salt spreader , try tapping it repeatedly, this may help to loosen up the salt. Step 6- Try Water If you have removed the excess salt as step 2 advised, you should not have too much salt left in your salt spreader. Now get some hot water to pour into your salt spreader. If it is a smaller handheld or manual walk behind spreader, your best bet would be to soak it in hot water. If you have a much larger salt spreader, clean it with hot water and a power washer.

Never leave salt in your spreader as it causes unnecessary problems. Always use clean, dry, free flowing salt. Make sure your spinner is set to the right height.

If the adjustment is off, it can jam the auger. If you have removed all salt and your spreader still is not working, check other parts to make sure they are not broken or in need of repairs.

If you leave salt in your spreader too long, it can corrode the gears and make your spreader unusable. Thanks for your interest in my products. THIS SPREADER REPAIR KIT WILL REPAIR THE FOLLOWING BUYERS SPREADERS: FITS MEYERS MINI JR. 5.75 CU FT MODEL 36008. Salt Spreader Repair Kit Unassembled. The item "Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008" is in sale since Wednesday, July 11, 2018. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Exterior\Snow Plows & Parts". The seller is "kennettplow" and is located in Cincinnati, Ohio.

This item can be shipped worldwide.

Salt Spreader Repair Kit Motor Spinner Auger, Hub & Lead Wire Fits Meyer 36008

Auger Kit New  Links  Contact Form  Privacy Policies  Service Agreement